EPSON TM T88II MODEL M129B DRIVER FOR MAC

If there is no paper jam and the printer has been printing for quite a while, the print head may be overheated. Page 42 Reference Information If your interface cable requires millimeter-type screws, replace the inch-type screws with the enclosed millimeter-type screws using a hex screwdriver 5 mm. Specified Thermal Roll Paper: Table Of Contents Unpacking General Problems, Printing Problems, Troubleshooting Press the printer cover until the cover audibly clicks into place.

Uploader: Jushicage
Date Added: 10 September 2015
File Size: 35.57 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 52409
Price: Free* [*Free Regsitration Required]

Page 52 Printed in Japan Printer Hexagonal lock screws only for the serial interface Modl the note on page for information about the hexagonal lock screws. Your printer has inch-type hexagonal lock screws installed.

Page 12 Other Qualified Suppliers for Thermal Paper The following suppliers sell thermal paper that may be used if desired. epson tm-t88ii model m129b

Unpacking The illustration below shows the items included for the standard specification printer. Reliability, Environmental Conditions Reliability Life: There are, however, some settings for users with special requirements.

Page 30 If there is no paper jam and the printer has been printing for quite a while, the print head may be overheated. IDN Card Epson model: Epson tm-t88ii model m129b of 52 Go.

Point of Sale Printer Paper Rolls

All our parts are epson tm-t88ii model m129b to be compatible with your Micros system. Appendix A tells how to epson tm-t88ii model m129b the DIP switch and paper near end settings. Page 36 Troubleshooting Serial interface specifications Set Open box printers do not include a power supply.

A-1 DIP switch functions. Do not touch the print head because it can be very hot after printing continuously for a long time. Connecting The Drawer 2.

Pull the cutter cover toward you so that you can rotate the cutter motor knob. Make sure the printer is turned off. Caution label above for the drawer kick-out connector.

If you use a paper roll with a core with an outside diameter of more than 18 mm, it epson tm-t88ii model m129b better to change to the upper setting, as described below. If your interface cable epson tm-t88ii model m129b millimeter-type screws, replace the inch-type screws with the enclosed millimeter-type screws using a hex screwdriver 5 mm. Open the printer cover, and remove the paper roll.

The connection of a non-shielded printer interface cable to this printer will invalidate the EMC standards of this device. If the print head is overheated, the printer will resume printing when the head has cooled usually within two or three minutes.

DIP switches should not be changed while the printer power is on. For a complete listing of topics, see the Contents. Self Test The self test lets you know if your printer is operating properly. Electrical Characteristics Supply voltage: Why should I buy Micros printers and supplies from Beagle Hardware?

01 – Roll Paper for POS Printers

The epzon cutter is jammed. Adjusting The Paper Near End Detector If epson tm-t88ii model m129b use a paper roll with a core with an epson tm-t88ii model m129b diameter of more than 18 mm, it is better to change to the upper setting, as described below.

Interface The shape of the interface Following the instructions on the label, rotate the knob until the appears in the hole. Page 32 To clear a paper jam, follow the steps below: If the printer has a serial interface, tighten the screws on both sides of the cable connector.

Tm-8t8ii you want to use this cover, install it as shown in the illustration below.

If there is no paper jam and the printer has been printing for quite a while, the print head may be overheated. Close the cover and turn off the printer or reset it to turn off the hex dump mode. If a foreign object, such as a push pin or paper clip, drops tm-t88iii the auto cutter and causes the auto cutter to lock up, the printer enters an error state epson tm-t88ii model m129b begins the recovery operation automatically.

Setting Up the Printer Using an incorrect power epson tm-t88ii model m129b may cause fire or electrical shock. Dpson a new paper roll, and the printer will continue printing.